Power/Volume/Sound Controls Power ON/OFF Turn the ignition switch to the ACC or ON position. Press the power/volume dial to turn the audio system on. Press the power/volume dial again to turn the audio system off. NOTE: Volume adjustment To adjust the volume, turn the power/ volume dial. Turn the power/volume dial to the right to increase volume, to the left to decrease it. Audio sound adjustment 1. Press the audio control dial to select the function. The selected function will be indicated. Standard audio-equipped model Bose Sound System-equipped model *1 Depending on the mode selected, the indication changes. 2. Turn the audio control dial to adjust the selected functions as follows: Standard audio-equipped model Bose� Sound System-equipped model NOTE: To reset bass, treble, fade, and balance, press the audio control dial for 2 seconds. The unit will beep and �CLEAR� will be displayed. Automatic Level Control (ALC) The automatic level control is a feature that automatically adjusts audio volume and sound quality according to the vehicle speed. The volume increases in accordance with the increase in vehicle speed, and decreases as vehicle speed decreases. Select the desired ALC mode. Turn the audio control dial to select ALC OFF or ALC LEVEL1―7 modes. The selected mode will be indicated. *AudioPilot� 2 (Bose� Sound Systemequipped model) AudioPilot� 2 automatically adjusts audio volume and sound quality in accordance with the level of noise entering the vehicle interior while driving. When AudioPilot� 2 is turned on, the system automatically calculates the conditions for optimum hearing of sound which may be difficult to hear depending on exterior noise. The system is also equipped to optimally adjust the acoustic characteristics automatically while the roof is open or closed. The acoustic adjustment occurs with the lock/unlock operation of the top latch on the roof, and while the adjustment is being done, the audio is muted for about 1.5 sec, and then fades in. * AudioPilot� 2 is a registered trademark of Bose Corporation. BEEP setting The beep-sound when operating the audio system can be set on or off. Time adjustment Rotating the audio control dial switches the display between 12 and 24-hour clock time. Clock Setting the time The clock can be set at any time when the ignition switch is in the ACC or ON position. 1. To adjust the time, press the clock button ( ) for about 2 secondsuntil a beep is heard. The clock's current time will flash. 2. To advance the hours, press the hour set button ( ). To advance theminutes, press the minute set button ( ) while the time is flashing. 3. Press the clock button ( )again to start the clock. NOTE: is released, the seconds are reset to �00�. - If the power supply to the unit is interrupted (if the fuse blows or the vehicle's battery is disconnected), the clock will need to be reset. Operating the Radio Radio ON Press a band selector button ( ) toturn the radio on. Band selection Successively pressing the band selector button ( ) switches the bandsas follows: FM1→FM2→AM. The selected mode will be indicated. If FM stereo is being received, �ST� will be displayed. NOTE: Tuning The radio has the following tuning methods: Manual, Seek, Scan, Preset channel, and Auto memory tuning. The easiest way to tune stations is to set them on preset channels. NOTE: Manual tuning Turning the manual tuning dial will change the frequency higher or lower. Seek tuning Pressing the seek tuning button ( ). NOTE: Scan tuning Press the scan button ( )to automatically sample strong stations. Scanning stops at each station for about 5 seconds. To hold a station, press the scan button ( ) again during thisinterval. Preset channel tuning The 6 preset channels can be used to store 6 AM and 12 FM stations. 1. To set a channel first select AM, FM1, or FM2. Tune to the desired station. 2. Depress a channel preset button for about 2 seconds until a beep sound is heard. The preset channel number and station frequency will be displayed. The station is now held in the memory. 3. Repeat this operation for the other stations and bands you want to store. To tune one in the memory, select AM, FM1, or FM2 and then press its channel preset button. The station frequency and the channel number will be displayed. NOTE: Auto memory tuning This is especially useful when driving in an area where the local stations are not known. Additional AM/FM stations can be stored without disturbing the previously set channels. Press and hold the auto memory button ( ) for about 2 seconds untila beep sound is heard; the system will automatically scan and temporarily store up to 6 stations with the strongest frequencies in each selected band in that area. After scanning is completed, the station with the strongest frequency will be tuned and its frequency displayed. Press and release the auto memory button ( ) to recall stations fromthe autostored stations. One stored station will be selected each time; its frequency and channel number will be displayed. NOTE: Operating the Satellite Radio Information display All operations of the satellite radio are displayed on the Information display. NOTE: These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Increase the separation between the equipment and tuner. - Connect the equipment into an outlet on a circuit different from that to which the tuner is connected. - Consult the dealer or an experienced radio/ TV technician for help. What is satellite radio? SIRIUS is radio the way it was meant to be: More than 100 new channels of digital quality programming delivered to listeners coast to coast via satellite. That means channels of completely commercial-free music plus more channels of news, sports, and entertainment from names like CNBC, Discovery, SCI-FI Channel, A&E, House of Blues, E!, NPR, Speed vision and ESPN. SIRIUS is live, dynamic entertainment, completely focused on listeners. Every minute of every day of every week will be different. All commercial-free music channels are created in-house and hosted by DJs who know and love the music. Do you like Reggae? How about Classic Rock or New Rock? SIRIUS has an array of choices spanning a vast range of musical tastes including the hits of the 50's, 60's, 70's, & 80's as well as Jazz, Country, Blues, Pop, Rap, R&B, Bluegrass, Alternative, Classical, Heavy Metal, Dance and many others. From its state-of-the-art, digital broadcasting facility in Rockefeller Center, New York City, SIRIUS will deliver the broadest, deepest mix of radio entertainment from coast to coast. SIRIUS will bring you music and entertainment programming that is simply not available on traditional radio in any market across the country. It's radio like you've never heard before. Sign up for SIRIUS Radio today! For more information, visit siriusradio.com. Satellite radio can be subscribed to and received in the United States. (Except Alaska and Hawaii) and Canada. How to subscribe to satellite radio Once the system is installed you must first subscribe to the SIRIUS Radio service to activate the system. The SIRIUS Radio service uses an ID code to identify your radio. This code is needed to subscribe to SIRIUS Radio, and if needed, is also used to report any problems should there be any in the future. Listeners can subscribe using any of the following methods: - Visiting SIRIUS on the web at www.sirius.com - Calling (888) 539-7474 - E-mail at: customercare@siriusradio. com NOTE: Satellite radio activation For activation and subscription information call toll-free at 1-888-539- SIRI (7474). A SIRIUS Customer Care representative will take the necessary information and walk you through the activation process. Or you can visit SIRIUS online at WWW.siriusradio.com and click on the �Join� button. When you call the SIRIUS Customers Care number you have two options available. (1) The full package which allows you access to all SIRIUS content except pay- per-view. (2) The family package which allows access to certain channels. Please see the website: www.sirius.com for details. Please have the following information ready when attempting to activate your service: - Valid credit card information (type, number, expiration date). When you are ready to receive the on-air activation signals you will be instructed (for activation via phone) to turn on your tuner, have the antenna pointed skyward, and to set the channel to channel 184. Once the signal is sent from the national studio it may take up to ten minutes to be received by your unit. NOTE: * ESN: Electronic Serial Number SIRIUS operation All operations of the satellite radio are conducted by means of the audio unit. SIRIUS radio mode selection When the satellite button is pressed during ACC ON, it will play the last SIRIUS channel in use before the mode was switched over to another mode or the power was turned off. When the satellite button is pressed in a mode other than the SIRIUS mode, the last channel in use will be received. Every time the satellite button is pressed, the bank changes in the order shown below. NOTE: Operation in the initial state It may take some time to start up the equipment when it is in the initial state, when there is a change in the user's subscription condition, or when the SIRIUS channel map is changed. �UPDATING xx%� is displayed when the SIRIUS channel map is changed. If the unit is initialized or the user contract content is changed, �UPDATING� is displayed. Updating could take as long as three minutes depending on the geographical area. When the unit is in an initialized state, channel 184 is displayed after the display indicates �UPDATING 100%�. If the SIRIUS channel map or the user contract content is changed, the channel prior to the change is displayed after �UPDATING� is displayed. After the initialization display, it may take as long as 12 seconds to receive channel 184. When the SIRIUS mode is switched to another mode, or when the power is turned off, the present channel which is being received is stored as the last channel. Channel selection Turning the manual tuning dial allows you to select the desired receiving channel. - Turn the knob clockwise: Channel Up - Turn the knob counterclockwise: Channel Down Unsubscribed channel When a selected station has not been subscribed to, the display indicates the following: NOTE: Invalid channel When a selected channel is not broadcasting, [SR (banknumber) INVALID] is displayed for one second, followed by [SR (bank number) CHANNEL], which is also displayed for one second. The display then returns to the previous valid channel. NOTE: Preset channel programming (Programming with �channel number� display) 1. Select the desired channel to be programmed. At this point, the following is displayed: (channel number)] 2. Keep pressing the channel preset button for 1.5 seconds or more. The programming process is complete after the channel number flashes. Then, [SR (bank number)] isdisplayed and a beep sound is heard at the same time. 3. [SR (bank number)CH (preset number) (channel number)] are displayed. (Programming with �text� display (e.g. channel name)) 1. Select the desired channel to be programmed. At
this point, the following is displayed: (selected text (e.g. channel name))] 2. Keep pressing the channel preset button for 1.5 seconds or more. The programming process is complete after the text (e.g. channel name). flashes. Then, [SR (banknumber)] is displayed and you will hear beep sound at the same time. 3. SR (bank number)CH (preset number) (channel number)] are displayed. 4. Three seconds later, it returns to normal display. [SR (bank number)(text (e.g. channel name)) NOTE: Preset channel call-up Press and release the channel preset button, CH (preset number) (channel number)] appears. When the preset button is pressed during text mode, its channel number is displayed first for three second and then its text is displayed. NOTE: Category change Press the category button (UP or DOWN). and select the desired category. - Press the category button (UP): Category up At this time, the lowest (smallest-number). channel within the category indicated is received. When the highest (or lowest) category is reached, the category is changed over in the order shown below. Highest category→ Category all → Lowest category NOTE: Channel selection within a category If category is not in �ALL� and the channel number is displayed, turning the manual tuning dial moves the channel number up/down in the present category. - Turn the manual tuning dial clockwise: Channel Up NOTE: Channel number, channel name, category, artist, song titles and info display Each time the text button is pressed during SIRIUS reception, the display of the text data is changed over in the order shown below. NOTE: - To display the rest of the characters of a long title, press and hold the text button (
). The display scrolls the (Channel number display) - When the text button is pressed while in info display mode, the mode changes to the channel number display mode. (Channel name display) - When the text button is pressed while in channel number display mode, it changes to channel name display mode. - There are short (eight fixed characters). and long names for the channel name. - The long name is displayed first, and three seconds later the short name is displayed. If there is no short name, the long name is displayed. - To display the rest of the characters of the channel name, press and hold the text button (TEXT). The display scrolls the next ten characters. Press and hold the text button (TEXT) again after the last ten characters have been displayed to return to the beginning of the title. - Press and hold the text button while the short name is displayed to switch the display to the long name. - Three seconds after scrolling the long name, the display automatically returns to the first part of the long name. Three more seconds and the short name appears. - If there is no channel name, �NO TITLE� is displayed. (Category name display) - When the text button is pressed while in channel name display mode, it changes to the category name display mode. - There are short (eight fixed characters). and long names for the category name. - The long name is displayed first, and three seconds later the short name is displayed. If there is no short name, the long name is displayed. - To display the rest of the characters of the category name, press and hold the text button (TEXT). The display scrolls the next ten characters. Press and hold the text button (TEXT) again after the last ten characters have been displayed to return to the beginning of the title. - Press and hold the text button while the short name is displayed to switch the display to the long name. - Three seconds after scrolling the long name, the display automatically returns to display the first part of the long name. Three more seconds and the short name appears. - If there is no category name, �NO CATEGORY� is displayed. (Artist name display) - When the text button is pressed while in category name display mode, it changes to the artist name display mode. - To display the rest of the characters of the artist's name, press and hold the text button (TEXT). The display scrolls the next ten characters. Press and hold the text button (TEXT) again after the last ten characters have been displayed to return to the beginning of the title. - Three seconds after scrolling the artist name, the display automatically return to display the first part of the artist's name. - If there is no artist's name, �NO ARTIST� is displayed. (Song title display) - When the text button is pressed while in artist name display mode, it changes to the song title display mode. - To display the rest of the characters of the song title, press and hold the text button (TEXT). The display scrolls the next ten characters. Press and hold the text button (TEXT) again after the last ten characters have been displayed to return to the beginning of the title. - Three more seconds after scrolling the song title, the display automatically returns to display the first part of the song title. - If there is no song title, �NO SONG� is displayed. (INFO (such as composer's name). display) - When the text button is pressed while in song title display mode, it changes to the INFO display mode. - To display the rest of the characters of the composer's name, press and hold the text button (TEXT). The display scrolls the next ten characters. Press and hold the text button (TEXT) again after the last ten characters have been displayed to return to the beginning of the title. - Three seconds after scrolling the text, the display automatically returns to display the first part of the text. - If there is no composer name, �NO INFO� is displayed. Instant replay This function allows you to rewind and replay the program that you were previously or are currently listening to. Press the instant replay button ( ). When the seek tuning button ( )is pressed (about 1.5 seconds), playback starts from the beginning of the current program. When the seek tuning button ( )is pressed twice, playback starts from the beginning of the previous program. When the seek tuning button ( )is pressed for about 1.5 seconds or longer, the program is reversed while the button is being pressed. When the seek tuning button ( ) is pressed (about 1.5 seconds), playback starts from the beginning of the next program. When the seek tuning button ( ) is pressed (about 1.5 seconds) while the last program is being played, the instant replay mode is cancelled. When the seek tuning button ( ) is pressed for 1.5 seconds or longer, the program is fast-forwarded while the button is being pressed. When pressing and holding the button until the end of the program, the instant replay mode is cancelled. When the instant replay button is pressed again, playback is paused, or playback starts if it has been paused. NOTE: - After turning on the power and switching to SIRIUS digital satellite radio mode, the instant replay mode is not available for several seconds after changing channels. Displaying the SIRIUS ID (ESN) When the ESN button is pressed for 1.5 seconds or longer, a 12-digit Electronic Serial Number (ESN) for the SIRIUS tuner is displayed. (If the SIRIUS ID (ESN) for the tuner does not display) If �ESN FAIL� isdisplayed after pressing the ESN button for 1.5 seconds or longer, contact an Authorized Mazda Dealer. Initialization of ID code If the registered ID code is forgotten, return the ID code to the default [0000] by performing the following steps: Setting condition: SAT mode (Master code input preparation) 1. Hold the scan button, then press channel preset button 4, hold both buttons together for 1.5 seconds. 2. �ENTER PIN� appears for three seconds which indicates that it is in code input mode. 3. �SR1 - - - -� appears, which indicates that it is ready for code input. (Master code input) 4. Input the master code using the channel preset buttons 1-4. (The master code is already set at the time of factory shipment.) (Master code input determination) 5. Determine the master code which has been input by pressing the scan button. 6. �PIN CLEARED� appears which indicates that the master code input has been completed. 7. The ID code is set to the default [0000] and the initialization process is completed. NOTE: SIRIUS Satellite Radio Master Code: [0913] NOTE: - If an ID code is not input for ten seconds, �Err� is displayed and it returns to the former display. - Channel preset buttons 1, 2, 3, 4 and the scan button are used for inputting the ID code. Buttons 5 and 6 cannot be used. Change of ID code Setting condition: SAT mode When changing the ID code, the new ID code is input after the previous one is input first. (Registered ID code input) 1. Hold the scan button, then press channel preset button 5, hold both buttons together for 1.5 seconds. 2. �ENTER PIN� appears for three seconds which indicates that it is in code input mode. 3. �SR1 - - - -� appears, which indicates that it is ready for code input. 4. Input the registered ID code using channel preset buttons 1-4. Example: When the registered ID code is �2323�, input �2323�. At this time �SR1 2323� is displayed. Press 1 for the first digit, 2 for the second, 3 for the third, and 4 for the last digit. For example, if your number is 2323, press 1 three times, 2 four times, 3 three, and 4 four times. If the display goes off while inputting, begin from Step 1. NOTE: (Verification with the registered ID code) 5. Determine the input code by pressing the scan button. 6. If it does not match with the previously registered code, �SR1 Err� is displayed and then it returns to �SR1 - - - -�. 7. If it matches with the previously registered code, �ENTER PIN� appears again and it switches to code input mode. 8. �SR1 - - - -� appears, and it is ready for input of the new ID code. (New ID code input) 9. Input the new ID code using channel preset buttons 1-4. Example: If �1234� is input as the new code, �SR1 1234� is displayed. (New ID code input determination) 10. Determine the new ID code which has been input by pressing the scan button. 11. �PIN CHANGED� appears for three seconds which indicates that the new ID code input has been completed. 12. It returns to the former display. NOTE: - Channel preset buttons 1, 2, 3, 4 and the scan button are used for input of the ID code. Buttons 5 and 6 cannot be used. Individual channel locking If a channel is locked, the channel is muted. NOTE: (Locking a channel) 1. Select a channel to be locked by turning the manual tuning dial. Example: Select channel 100 (Registered ID code input preparation) 2. Hold the scan button, then press channel preset button 6, hold both buttons together for 1.5 seconds. 3. �ENTER PIN� appears for three seconds which indicates that it is in code input mode. 4. �SR1 - - - -� appears which indicates that it is ready for code input. (Registered ID code input) 5. Input the registered ID code using channel preset buttons 1-4. Example: If the registered ID code is �2323�, input �2323�. At this time �SR1 2323� is displayed. (Registered ID code input determination) 6. Determine the code which has been input by pressing the scan button. 7. If it does not match the registered code, �SR1 Err� is displayed and then it returns to �SR1 - - - -�. 8. If it matches the registered code, �SR1 LOCK� appears for three seconds which indicates that the code input has been completed. 9. �SR1 LOCK 100� appears which indicates that the parental lock is activated. At this time, mute is on and no sound is heard. NOTE: - Channel preset buttons 1, 2, 3, 4 and the scan button are used for input of the ID code. Buttons 5 and 6 cannot be used. Lock cancellation Setting condition: SAT mode (Releasing a locked channel) 1. Select a channel to be released by turning the manual tuning dial. Example: Select the locked channel (i.e. 100). At this time, �SR1 LOCK 100� is displayed. (Registered ID code input preparation) 2. Hold the scan button, then press channel preset button 6, hold both buttons together for 1.5 seconds. 3. �ENTER PIN� appears for three seconds which indicates that it is in code input mode. 4. �SR1 - - - -� appears, which indicates that it is ready for code input. (Registered ID code input) 5. Input the registered ID code using channel preset buttons 1-4. Example: When the registered ID code is �2323�, input �2323�. At this time �SR1 2323� is displayed. NOTE: (Registered ID code input determination) 6. Determine the input code by pressing the scan button. 7. If it does not match the registered code, �SR1 Err� is displayed and then it returns to �SR1 - - - -�. 8. If it matches the registered code, �SR1 UNLOCK� appears for three seconds which indicates that the code input has been completed. 9. �SR1 100� appears which indicates that the parental lock is off. At this time, sound is heard. NOTE: - Channel preset buttons 1, 2, 3, 4 and the scan button are used for input of the ID code. Buttons 5 and 6 cannot be used. Error signs (1) Depending on the surrounding conditions (such as large trees, buildings, or tunnels) and special weather conditions, the reception of SIRIUS radio waves may be decreased or temporarily interrupted. �ACQUIRING� may appear. (2) In case of an antenna malfunction, �ANTENNA FAIL� is displayed. Check the satellite radio antenna, antenna cable and DLP antenna connector. NOTE: * DLP: Down Link Processor (SATELLITE RADIO Module) Operating the Compact Disc (CD) Player NOTE: Inserting the CD Insert the CD into the slot, label-side up. The auto-loading mechanism will set the CD and begin play. NOTE: Ejecting the CD Press the CD eject button ( ) to eject the CD. Playback Press the CD play button ( ) to start play when a CD is in the unit. If a CD is not in the unit when the CD play button ( ) is pressed,�NO DISC� will flash on and off. NOTE: Pause To stop playback, press the Play/Pause button ( ). Fast-forward/Reverse Press and hold the fast-forward button ( ) to advance through a trackat high speed. Press and hold the reverse button ( ) to reverse through a track at high speed. Track search Press the track up button ( ) once to skip forward to the beginning of the next track. Press the track down button ( ) once to skip back to the beginning of the current track. Folder search (during MP3/WMA CD playback) To change to the previous folder, press the folder down button ( ), orpress the folder up button ( ) to advance to the next folder. Music scan This feature helps to find a program by playing about the first 10 seconds of each track. Press the scan button ( )during playback to start the scan play operation (the track number will flash). Press the scan button ( )again to cancel scan playback. NOTE: Repeat playback During music CD playback 1. Press the repeat button ( ) duringplayback to play the current track repeatedly. �RPT� is displayed. 2. Press the button again to cancel the repeat playback. During MP3/WMA CD playback (Track repeat) 1. Press the repeat button ( ) duringplayback to play the current track repeatedly. After �TRACK RPT� is displayed, �RPT� is displayed. 2. To cancel the repeat playback, press the button again after 3 seconds. (Folder repeat) 1. Press the repeat button ( ) duringplayback, and then press the button again within 3 seconds to play the tracks in the current folder repeatedly. After �FOLDER RPT� is displayed, �F-RPT� is displayed. 2. Press the button again to cancel the repeat playback. Random playback Tracks are randomly selected and played. During music CD playback 1. Press the random button ( ) duringplayback to play the tracks on the CD randomly. �RDM� is displayed. 2. Press the button again to cancel the random playback. During MP3/WMA CD playback (Folder random) 1. Press the random button ( ) during playback to play the tracks in the folder randomly. After �FOLDER RDM� is displayed, �RDM� is displayed. 2. To cancel the random playback, press the button again after 3 seconds. (CD random) 1. Press the random button ( ) duringplayback, and then press the button again within 3 seconds to play the tracks on the CD randomly. After �DISC RDM� is displayed, �D-RDM� is displayed. 2. Press the button again to cancel the random playback. Switching the display For files with a file name or other name that have been input, the display changes in the order of the file names or other names each time the text button ( ). Music CD MP3/WMA CD NOTE: This unit can only read English (including numerals) one-byte characters. Depending on the CD writing software used, proper display may not be possible. Display scroll Only 13 characters can be displayed at one time. To display the rest of the characters of a long title, press and hold the text button ( ). The displayscrolls the next 13 characters. Press and hold the text button ( ) again after the last 13 characters have been displayed to return to the beginning of the title. NOTE: Message display If �CHECK CD� is displayed, it means that there is some CD malfunction. Check the CD for damage, dirt, or smudges, and then properly reinsert. If the message appears again, take the unit to an Authorized Mazda Dealer for service. Message display If �CHECK CD� is displayed, it means that there is some CD malfunction. Check the CD for damage, dirt, or smudges, and then properly reinsert. If the message appears again, take the unit to an Authorized Mazda Dealer for service. Operating the In-Dash CD Changer NOTE: Inserting the CD The CD must be label-side up when inserting. The auto-loading mechanism will set the CD and begin play. NOTE: A CD cannot be inserted while the display reads �WAIT�. A beeping sound can be heard during this waiting time. There will be a short lapse before play begins while the player reads the digital signals on the CD. Normal insertion 1. Press the load button ( ). Inserting CDs into desired tray number 1. Press and hold the load button ( ). 2. Press the channel preset button for the desired tray number while �WAIT� is displayed. 3. When �IN� is displayed, insert the CD. NOTE: Multiple insertion 1. Press and hold the load button ( ). 2. When �IN� is displayed, insert the CD. 3. When �IN� is displayed again, insert the next CD. NOTE: - The CD trays are full. Ejecting the CD Normal ejection 1. Press the CD eject button ( ). The disc number and �DISC OUT� will be displayed. 2. Pull out the CD. NOTE: Ejecting CDs from desired tray number 1. Press and hold the CD eject button ( ). The �DISC OUT� display flashes. 2. Press the channel preset button for the desired CD number for less than 5 seconds after the beep sound is heard. 3. Pull out the CD. Multiple ejection 1. Press and hold the CD eject button ( ). The �DISC OUT� display flashes. 2. Pull out the CD, then the next CD will be ejected. NOTE: - All CDs in the tray will be ejected continuously. - CDs can be ejected when the ignition
switch is off. Press and hold the CD eject button ( ) for about 2 seconds Playback Press the CD play button ( )to start play when a CD is in the unit. If a CD is not in the unit when the CD play button ( ) is pressed,�NO DISC� will flash on and off. Pause To stop playback, press the Play/Pause button ( ). Fast-forward/Reverse Press and hold the fast-forward button ( ) to advance through atrack at high speed. Press and hold the reverse button ( ) toreverse through a track at high speed. Track search Press the track up button ( ) once to skipforward to the beginning of the next track. Press the track down button ( )once to skip back to the beginning of the current track. Disc search During music CD playback To change the disc, press the DISC button ( ) during playback. during playback. Folder search (during MP3/WMA CD playback) To change to the previous folder, press the folder down button ( ) forless than 1.5 seconds, or press the folder up button ( ) for less than 1.5 seconds to advance to the next folder. Music scan This feature helps to find a program by playing about the first 10 seconds of each track. Press the scan button ( )during playback to start the scan play operation (the track number will flash). Press the scan button ( )again to cancel scan playback. NOTE: Repeat playback During music CD playback 1. Press the repeat button ( ) during playback to play the current track repeatedly. �RPT� is displayed. 2. Press the button again to cancel the repeat playback. During MP3/WMA CD playback (Track repeat) 1. Press the repeat button ( ) duringplayback to play the current track repeatedly. After �TRACK RPT� is displayed, �RPT� is displayed. 2. To cancel the repeat playback, press the button again after 3 seconds. (Folder repeat) 1. Press the repeat button ( ) duringplayback, and then press the button again within 3 seconds to play the tracks in the current folder repeatedly. After �FOLDER RPT� is displayed, �F-RPT� is displayed. 2. Press the button again to cancel the repeat playback. Random playback Tracks are randomly selected and played. During music CD playback 1. Press the random button ( ) during playback to play the tracks in the CD randomly. �RDM� is displayed. 2. Press the button again to cancel the random playback. During MP3/WMA CD playback (Folder random) 1. Press the random button ( ) duringplayback to play the tracks in the folder randomly. After �FOLDER RDM� is displayed, �RDM� is displayed. 2. To cancel the random playback, press the button again after 3 seconds. (CD random) 1. Press the random button ( ) duringplayback, and then press the button again within 3 seconds to play the tracks on the CD randomly. After �DISC RDM� is displayed, �D-RDM� is displayed. 2. Press the button again to cancel the random playback. Switching the display For files with a file name or other name that have been input, the display changes in the order of the file names or other names each time the text button ( ). is pressed during playback. Music CD MP3/WMA CD NOTE: This unit can only read English (including numerals) one-byte characters. Depending on the CD writing software used, proper display may not be possible. Display scroll Only 13 characters can be displayed at one time. To display the rest of the characters of a long title, press and hold the text button ( ). Thedisplay scrolls the next 13 characters. Press and hold the text button ( ) again after the last 13 characters have been displayed to return to the beginning of the title. NOTE: Message display If �CHECK CD� is displayed, it means that there is some CD malfunction. Check the CD for damage, dirt, or smudges, and then properly reinsert. If the message appears again, take the unit to an Authorized Mazda Dealer for service. Operating the Auxiliary jack You can connect portable audio units or similar products on the market to the auxiliary jack to listen to music or audio over the vehicle's speakers, refer to Auxiliary Input. Error Indications If you see an error indication on the display, find the cause in the chart. If you cannot clear See also:Happy-Face Looks Engine Compartment Overview In Case of an Emergency |