How do you reprogram a schlage door lock

Resetting a Schlage door lock requires first clearing the device and then restoring the default codes. There are a number of reasons you may want to reset a Schlage door lock, ranging from forgetting the code to getting an error alert from the device itself. To help burglarproof your home, it's also smart to reset door locks when moving into a new home.

Advertisement

Video of the Day

If you need to reset your Schlage door lock, it's a fairly simple task that can be accomplished in just a few steps, which makes it easy to change the code from time to time for a bit of added home security. Homeowners can do the reset themselves with nothing more than a Phillips screwdriver and a factory preset code.

Step 1: Locate the Factory Preset Code

Reset a Schlage door lock by first finding the factory/default codes for the device. These codes are always included in the user guide that came with the lock set. If you don't have this guide handy, you can also find the codes on the sticker that is located either on the inside or outside of the lock itself. Make sure you don't skip this step, as these codes will be required for full setup, and the manufacturer can't help you with this if they are lost.

Advertisement

Step 2: Open the Lock Housing

Open the lock housing by using a Phillips screwdriver to remove the screws that hold it onto the back of the lock. Some units may have a decorative battery cover that you'll need to lift off prior to unscrewing the housing. When this is complete, look for the white sticker that has the preset codes if you don't already have them. Write these down, leaving the battery cover/back of the unit off so that you can access the battery or use the reset button.

Advertisement

Step 3: Push Reset Button or Disconnect Battery

Reset the Schlage lock by engaging the reset button if one is available, or by disconnecting the battery. Once the cover and housing are removed, if the button is there, simply press and hold it until the red light isn't flashing anymore. Release it and wait until the lock resets itself and the light turns blue.

If your Schlage door lock doesn't have a reset button available, you'll need to do clear the lock codes manually by disconnecting the battery. This will prepare the unit for a reset.

Advertisement

Step 4: Clear the Door Lock Codes

Clear the current door lock codes by pressing and holding the Schlage button on the front of the lock until it turns green. Then release it and reconnect the battery within the next 10 seconds. Press and hold the Schlage button again until you hear a beep.

Step 5: Reset the Lock

Enter a factory preset code to make sure the lock has reset. Once you do this, the lock will go through a setup process. Let it complete this on its own. When it finishes, the lock is ready to be reset with your new codes.

Our home security is always one of our top priorities. With the range of Schlage locks on the market, we can surely enjoy the day outside or sleep soundly, knowing we are safe and well secured.

But there might be instances when we need our Schlage lock reset and restored to the factory setting to optimize its use and for our peace of mind.

You have landed here, probably pondering on the idea and wondering how to reset a Schlage door lock. Stick with us as we guide you on the process, with our quick and easy step-by-step procedures below.

Table of Contents

  • Reminder Before You Start Resetting Code on Schlage Lock
  • How to Reset Schlage Encode Smart Wifi Locks
  • How to Reset Sense Smart and Connect Smart Locks
  • How to Reset Schlage Keypad Lock Models and Schlage Touch Keyless Touchscreen
  • Helpful Tips
  • Conclusion

Reminder Before You Start Resetting Code on Schlage Lock

Factory default reset will wipe out all data saved in the unit. All existing user codes, pairings, and other devices will not work and will no longer be recognized by the lock.

Prepare the default programming code and user codes before any attempt to restore to the original factory settings and reprogramming Schlage lock. The codes are either on the back or front of the User Guide that came with the unit you received.

As a backup, there is a sticker with the default codes on the lock’s interior itself; an easy and quick disassembly is needed to locate it. You might need a screwdriver to open and get it in some units.

Do not try to factory reset without code. Schlage Customer Service will not be able to provide or retrieve any lost default codes.

How to Reset Schlage Encode Smart Wifi Locks

How do you reprogram a schlage door lock

  • Remove the battery panel cover.
  • Press the reset button; the black button on the right of the thumb turns inside your lock.

Keep pressing the button until the red LED light stops blinking (it usually takes more or less 8 seconds).

  • Wait for the LED light to flash to a steady blue (typically takes 10 seconds.
  • The process to reset Schlage encode keypad lock is now complete.

How to Reset Sense Smart and Connect Smart Locks

  • Take off the battery panel cover.
  • Disconnect your lock’s battery.
  • Tap and hold the “Schlage” button on the front panel of the lock.
  • Simultaneously, reconnect the battery while still holding on to the “Schlage” button on the front panel.
  • Let go of the “Schlage” button.

A check mark will flash three times if the lock’s reset process is successful.

  • Press the “Schlage” button and enter any of the default user codes to confirm.

The lock will do a setup routine. Observe the bolt’s movement until it stops, confirming the completion of the Schlage smart lock reset process.

How to Reset Schlage Keypad Lock Models and Schlage Touch Keyless Touchscreen

How do you reprogram a schlage door lock

  • Take off the panel cover and the battery.
  • Power down the lock by disconnecting the battery.
  • Press the “Schlage” button once.

  • Note: Make sure it will not take more than 10 seconds to complete Step 4 to Step 6, or you will need to start over again.

  • Quickly reconnect the battery.

The LED indicator will light up, flashing green for a second.

  • Tap and hold the “Schlage” button until it flashes green and creates a beeping sound.
  • Enter any of the default user codes.

If it has unlocked successfully, you can then change the programming code of your preference and add more user codes.

If it does not work and will not unlock, go back and start from step 3.

Helpful Tips

IFPOSSIBLE CAUSE/SUGGESTIONThe lock is no longer responsive but has a working battery.Possibly because of some issue with the internal workings, resetting might clear the unit and do the fix.You are getting a red light or an X, even after entering the correct user codes.The lock might have been dead for quite a long time, and the codes might have been erased or a sign of altered programming code, so resetting and reprogramming are needed.You forgot the programming code.Restore it to the default code and reprogram.You move the lock from one door to another, or you have moved to a new house.Reset Schlage lock code for security and peace of mind.You want to clear and delete all users and unpair all devices connected to the lock.Reset and reprogram.You are using an Apple Homekit and want to move the lock or add an Android device.Restoring to factory default setting is necessary to pair the lock again to the Schlage Home app thru the Schlage system.

Conclusion

With all the convenience and security these electronic and smart locks provide, we should well know how we can use them in the best possible way, and always be on top as much as possible, no matter what.

Whether we quickly access our locks with a key, with just a tap, or with our voice, knowing how to reset a Schlage door lock is valuable information for Schlage lock owners, which comes in handy in case unexpected circumstances arise.

Taking note of the steps, tips, and reminders, we can be at ease, knowing our locks stay safe and secure.

5/5 - (2 votes)

How do you reprogram a schlage door lock

Justin Williams

I am the last member to join Revolar and might be just the luckiest to work with dedicated people like Teddy and John. Our team has established a process where my only job is writing the best content to deliver incredible ideas and guides.

How do I reset my Schlage Lock code if I forgot the code?

The default programming code is printed on a label on the programming guide that came with your lock. If you do not have access to the guide, remove the lock from the door and look on the back of the lock for a label containing the default code.

How do you manually program a Schlage Lock?

While the deadbolt is locked, press the Outside Schlage Button and then enter a 4-8 digit User Code to unlock the deadbolt. Within 5 seconds, manually lock and unlock the deadbolt using the thumbturn. To restore Auto-Lock, simply lock the deadbolt using the thumbturn.

How do you reset a Schlage Lock for a new owner?

Like the Schlage Encode Smart WiFi Deadbolt, the Factory Default Reset of your Schlage Connect Smart Deadbolt with Z-Wave Plus technology can also be accomplished by holding the Enrollment button on the lock for seven seconds. The LED lights will indicate if the reset was successful.