How to open round padlock without key

There may come a time when you need to remove a disc lock without a key. Whether the key is lost or stolen, or you don’t have it handy, there are several methods you can try to get the lock off. In this article, we’ll show you how to remove a disc lock without a key.

If you lose your key or it’s stolen, you may not be able to access your property. In some cases, you may even need to remove the lock to prevent someone from stealing your property. There are several methods you can use to remove a disc lock without a key – keep reading for instructions!

Things You’ll Need

You’ll need a few basic tools to remove a disc lock without a key. The first is a flathead screwdriver. You’ll also need a wire hanger or coat hanger and some pliers. You may also need some WD-40 or lubricant if the lock is stuck.

• Flathead screwdriver
• Wire hanger or coat hanger
• Pliers
• WD-40 or lubricant

6 Methods to Follow on How to Remove a Disc Lock Without a Key

Method 1: Use a Screwdriver

If you have a flathead screwdriver, you can use it to remove the lock. First, use the screwdriver to pry the center of the disc outward. The gap in the center of the disc should allow you to stick your screwdriver inside. Once there’s enough room, work it back and forth until you can pull the lock off.

Step 1:

Line up your flathead screwdriver with the center of the disc lock. Apply enough pressure that the disc is slightly bent outward.

Step 2:

Work your way around the edge of the lock until you can pull it off with your hands. If you can’t get a grip on it to pull it off, use pliers instead.

Method 2: Use a Wire Hanger or Coat Hanger

If you don’t have a flathead screwdriver, you can still remove the lock without a key. The best option is to use a wire hanger or coat hanger. First, you’ll need to straighten out the steel wire, so it’s very rigid. Once you have this done, stick one end of it into the disc center and push down until the lock pops off.

Step 1:

Straighten out a wire hanger or coat hanger as straight as possible.

Step 2: 

Insert one end of the wire into the disc center and press until it pops off.

Step 3: 

If you have lubricant or WD-40, you’ll also need to spray the lock with it before trying to remove it. This will help loosen up any rust or dirt that’s keeping the disc stuck in place.

Method 3: Use Pliers

If you don’t have a wire hanger, coat hanger, or flathead screwdriver, you’ll need to use the last remaining removal method. It’s a bit more difficult than the previous methods and may require some extra elbow grease. You can try to remove the lock with pliers if it’s stuck in place. Make sure that you don’t bend or break the rubber coating around the lock when you try this. You can use WD-40 or lubricant to make it easier.

Step 1:

Stick the pliers into the disc center and try to remove the lock by applying pressure. Remember not to bend or break the rubber coating, so you don’t damage any parts of your motorcycle.

Step 2: 

If the lock doesn’t pop off, try lubricating it with WD-40 first. If that still doesn’t work, try using a wire hanger or coat hanger before resorting to pliers.

Method 4: Use Heat

You’ll need to use heat if you still can’t remove the lock after trying all of these methods. There are several ways to apply heat, including using a blow torch, but you should only resort to this method as your last resort. Ensure the motorcycle isn’t in direct sunlight or close to any flammable objects because it could catch on fire.

Step 1:

To use heat, you can either try using a blow torch. If this doesn’t work, you can also lay the bike over on its side, facing up the disc lock. Then try setting it on fire by holding a lighter underneath it until it smokes and melts off. Apply the heat slowly and never directly on top of any plastic parts because it can melt them.

Step 2:

If using heat doesn’t work, you’ve exhausted all your options for how to remove a disc lock without a key. Your only option is to find a locksmith who can help you pick it open or cut it off.

Method 4: Use a Drill

Don’t have any of the tools we mentioned above? Then you’ll need to use a drill. This isn’t easy to do, though, so you may need help from someone who has experience using one of these drills. The type of drill that works best is the rotary style with a long bit.

Step 1:

Take your drill and find an appropriate-sized bit to drill into the disc lock. Make sure the bit is longer than the lock, so you have enough space to drill into it.

Step 2:

With a friend holding the motorcycle steady, slowly drill a hole through the center of your disc lock until it pops off. Depending on how stubborn your lock is, this may take a long time, but that’s how you remove a disc lock without a key.

Method 5: Use Heat, Drill, and Pliers

Don’t have any of the tools we mentioned above? You can still try using heat, drilling it open with a drill, and removing it with pliers. This is how you remove a disc lock without a key by bringing together all of the removal methods we mentioned above for how to remove a disc lock without a key. We recommend trying this last because you’ll need help from someone who knows how to use pliers, drill, and has access to heat.

Step 1:

Find an appropriate-sized bit for your drill that’s long enough to drill into the disc lock. You can also use a blow torch and set the lock on fire if you don’t have a drill.

Step 2:

Once you’ve drilled a hole in your disc lock, spray it with WD-40 or lubricant to help loosen up the dirt and rust that’s keeping it stuck. Then try removing it with your pliers.

Method 6: Call a Locksmith

This method requires more time and money, but it is the most surefire way to get your bike back. Go ahead and call a locksmith (or two); some may be able to pick the lock for you, while others may need to drill it off. This is how I got my motorcycle out of impound using this method.

Step 1:

You will need to call a locksmith/mechanic willing to pick your lock. Please ensure the charges by how long it takes him and not how many attempts. Some locksmiths are good at picking these disc locks, while others might drill them off instead of risking damaging your steering column or exterior of the bike.

Don’t forget to tip your locksmith.

Step 2:

The locksmith will call you once the lock is removed. Pay him, give him a tip, AND thank him for not cutting your lock. He may have also saved your bike from being impounded or ticketed in the process, so be nice when talking with these guys.

I hope that your motorcycle isn’t stranded anywhere, but if it is, remember these methods. Also, please be careful how you treat a disc lock and store them. I hope this helps!

Frequently Asked Question

Can You Cut a Disc Padlock with Bolt Cutters?

Can you cut a disc padlock with bolt cutters? The answer is yes, you can. However, it’s not as easy as just snapping the lock off like you would a regular padlock. It takes more force and effort to cut through the metal disc.

If you’re looking for an easier way to cut a disc padlock, we recommend using a hacksaw blade. The hacksaw blade will give you a cleaner cut and make it easier to break the lock off.

How Do You Open a Locked Disk with A Drill?

Drilling into a locked disk is one way to open it without the key. You’ll need a drill with an appropriately-sized bit and someone to help you hold the motorcycle steady. Drill into the center of the lock until it pops off.

If you don’t have a drill, you can try using heat, a hacksaw blade, or pliers. These methods are less reliable than drilling, but they may work if you’re desperate. If all else fails, you can always call a locksmith to open the disk for you.

How Do You Open a Circle Lock without A Key?

There are several ways to open a circle lock without a key. The most common way is to drill into the lock and then use pliers to remove it. You can also try using heat, a hacksaw blade, or brute force to break the lock off. If all else fails, you can always call a locksmith to open the lock for you.

Is It Easy to Cut a Lock with Bolt Cutters?

It is easy to cut a lock with bolt cutters, but it takes more force than snapping off a regular padlock. If you’re looking for an easier way to cut a disc padlock, we recommend using a hacksaw blade.

Conclusion

If you have lost your disc lock key or it has been stolen, there is no need to worry. You can still remove the disc lock without the key. All you need is patience and some common tools that you may already have in your toolbox. Follow these simple steps to remove your disc lock without the key and get back on the road in no time. Thanks for reading our post about how to remove a disc lock without a key.Save0

You Can Check It Out To Does a Helmet Lock Work